Free shipping for orders more that $200
Free shipping for orders more that $200

Cart

Your cart is currently empty.

Continue shopping
1 / 3

1064nm Laser Ranging Target Designator 15km

Chat With Us

Reply within 24 hours

Delivery Time

3-5 days after payment

Shipment

Air freight

DESCRIPTION

The LDR80K2 Laser Designator adopts a transceiver co-aperture lens. It uses an LDA-pumped Nd: YAG crystal combined with an electro-optical Q-switching technology solution to achieve a typical 1064nm pulsed laser output. The single-pulse energy is 80 mJ, and the beam divergence angle is 0.25mrad. It employs an adaptive non-temperature-control  technology, allowing it to start working immediately. The entire device can operate for 90 seconds, pause for 60 seconds within Man ambient temperature range of -40°C to 60°C; 4 cycles (at normal or low temperatures); 1 cycle (at a high temperature of 60°C). It can be compatibly installed and applied in miniaturized electro-optical pods on airborne platforms, loitering munitions, and other combat platforms, realizing continuous ranging and periodic illumination of targets. It is an important laser device in the implementation of semi-active systems.

TECHNICAL SPECIFICATIONS

  Parameter Indicators
Module LDR80K2
Pump Source Laser LD (Laser Diode) Pumping
Cooling Method Passive cooling, no temperature control
Working Mode Laser Ranging, Laser target indication
Operating Wavelength 1064nm±1nm
Pulse Energy ≥80mJ
Laser Energy Stability Within a single irradiation cycle, the pulse energy fluctuation does not exceed 10% of the average energy.
Pulse Width ≥15ns±5ns
Beam Divergence Angle ≤0.25mrad
Stability of The Laser Optical Axis ≤0.05mrad
   Ranging performance
Ranging frequency 1~20Hz
Continuous Laser Ranging Time 5min(1Hz)/1min (5Hz)/20S(20Hz)
Minimum measuring distance ≤300m
Maximum measuring distance

≥15km (Under the conditions of a target with a size of 2.3m×2.3m, a diffuse reflectance coefficient of not less than 0.2, a visibility of not less than 23 km, and a relative humidity of not more than 70%)

Ranging accuracy ±1m
Rate of successful measurement 98%

 

MECHANICAL DIMENSION(mm)

 

APPLICATION NOTES

The LDR80K2 laser designator uses a transceiver co-aperture lens with an LDA-pumped Nd:YAG crystal and electro-optical Q-switching to produce a typical 1064nm pulsed output in ranging and target indication modes. Single-pulse energy is 80mJ, beam divergence ≤0.25mrad and laser optical axis stability ≤0.05mrad, with in-cycle pulse fluctuation not exceeding 10% of average energy and pulse width ≥15ns±5ns. Maximum measuring distance is ≥15km against a 2.3m by 2.3m target of diffuse reflectance ≥0.2, visibility ≥23km and relative humidity ≤70%, at 1~20Hz with ±1m accuracy, a 98% success rate and a minimum measuring distance of ≤300m. The adaptive non-temperature-control design lets the unit start working immediately, and the stated duty cycle is 90 seconds working with 60 seconds pause over -40°C to +60°C: 4 cycles at normal or low temperature and 1 cycle at 60°C. Co-aperture optics, immediate start and that cycle structure are suited to miniaturized electro-optical pods on airborne platforms and to loitering munitions, where continuous ranging and periodic illumination must run inside a fixed volume and thermal budget, the semi-active arrangement the site's guidance notes describe.

SELECTION GUIDANCE

Select the LDR80K2 when 15km of measurement, 80mJ of indication energy and a 90-second working cycle with 60-second pause match the mission profile, and when the platform is a small pod or loitering munition that must begin working without a temperature soak. If the mission needs continuous ranging for minutes rather than tens of seconds, the higher models state 5 minutes working at 1Hz, 1 minute at 5Hz and 20 seconds at 10Hz. If more range is required, the 20km model states ≥20km at ≥100mJ with ≤0.15mrad divergence under the same ≥23km visibility. If a shorter standoff with a lighter module is the real constraint, the 40mJ and 25mJ members are specified at ≥10km and ≥5,000m with wider divergence and, for the 25mJ member, ±2m accuracy. Acceptance should verify the ≥15km distance under the stated visibility and target conditions, 80mJ pulse energy, ≤0.25mrad divergence, ≤0.05mrad axis stability, ±1m accuracy, the 98% success rate, ≤300m minimum distance, the -40°C to +60°C range and the 4-cycle normal with 1-cycle high-temperature duty statement.

FREQUENTLY ASKED QUESTIONS

What is the maximum measuring distance of the LDR80K2 laser designator?
It reaches >=15km for a 2.3m x 2.3m target with a diffuse reflectance coefficient of not less than 0.2, a visibility of not less than 23 km and a relative humidity of not more than 70%.

What is the single-pulse energy and beam divergence angle of the LDR80K2?
The single-pulse energy is 80mJ and the beam divergence angle is 0.25mrad, with a 1064nm pulsed laser output.

What is the ranging frequency and ranging accuracy of the LDR80K2?
The ranging frequency is 1~20Hz and the ranging accuracy is +/-1m.

Does the LDR80K2 need temperature control to start working?
No, it uses adaptive non-temperature-control technology so it can start working immediately.

How long can the LDR80K2 run continuously?
It can operate for 90 seconds and pause for 60 seconds within an ambient temperature range of -40C to 60C, for 4 cycles at normal or low temperatures and 1 cycle at a high temperature of 60C.

ORDERING INFORMATION

Is there a minimum order quantity?
There is no minimum order quantity. Single units and evaluation samples are accepted.

What is the sample lead time?
Samples are shipped within 1 week after order confirmation.

What is the batch production lead time?
Batch production is delivered within 1 month after order confirmation.

RELATED TECHNICAL GUIDES

Further ERDI Laser engineering references on 1064 nm laser designation and target designation payloads:

1064nm Laser Ranging Target Designator 20km 1064nm Laser Ranging Target Designator 20km 1064nm Laser Ranging Target Designator 20km

You may also like