Free shipping for orders more that $200
Free shipping for orders more that $200

Cart

Your cart is currently empty.

Continue shopping

1570nm Laser EMC Testing Explained

Oct 10, 2026 Ran Haochen
1570 nm Laser EMC Testing

The 1570nm laser, with its advantages of low loss and long transmission distance, is widely used in backbone network communication, coherent optical modules, laser detection and other scenarios. This device is not a pure optical component. It is equipped with a built-in driver, TEC temperature control, high-speed modulation and power supply circuits. During operation, it generates electromagnetic interference and is susceptible to external electromagnetic disturbances, which can cause wavelength deviation, optical power jitter, modulation distortion and other problems. Therefore, EMC electromagnetic compatibility testing is a key step for its mass production certification and practical application.

Key takeaways

  • The 1570nm laser is not a pure optical component: its built-in driver, TEC temperature control, high-speed modulation and power supply circuits both generate electromagnetic interference and are susceptible to it.
  • Interference shows up as wavelength deviation, optical power jitter and modulation distortion, which is why EMC testing is a key step for mass production certification and practical application.
  • Standard testing uses a 10-meter semi-anechoic chamber, or a 3-meter chamber for small samples, covering 150 kHz to 6 GHz with background noise well below the test limits.
  • Emission testing covers conducted emission from 150 kHz to 30 MHz through a LISN with limits per EN 55032, and radiated emission from 30 MHz to 6 GHz.
  • Immunity testing covers electrostatic discharge, electrical fast transients, surge, and radio frequency radiation and conduction from 80 MHz to 6 GHz.
  • Qualification requires a dual judgement on electrical performance and on optical parameters such as wavelength, optical power and modulation accuracy.

1570nm laser standard EMC testing environment

Test site

The conventional method employs a 10-meter half-wave anechoic chamber. For small samples, a 3-meter anechoic chamber can be used. The entire site is covered with absorbing materials, and the background noise is much lower than the test limit, covering the entire test frequency range from 150 kHz to 6 GHz. An internal 360° insulated rotating turntable and an antenna elevation tower are equipped to meet the requirements for comprehensive signal acquisition.

Core testing equipment

LISN Impedance Stabilization Network: Filters out grid noise, stabilizes line impedance, and accurately collects power port conducted interference;

EMI Receiver/Spectrum Analyzer: Captures electromagnetic interference signals across the 150kHz to 6GHz frequency range;

Multi-band Test Antenna: Covers low, medium, and high frequency band radiation and emission tests;

EMS Test System: Includes electrostatic, pulse group, surge, and radio frequency interference generation modules;

Optical Monitoring Equipment: Optical power meter, wavelength analyzer, oscilloscope, for real-time monitoring of laser working parameters.

1570nm laser core EMC testing project

The test is divided into two categories: EMI self-interference emission and EMS external interference resistance. These are mandatory testing items in the industry.

Electromagnetic emission test

1. Conductive Emission (CE)
The test frequency range is 150kHz to 30MHz. The conducted voltage of the power supply and control port is collected through LISN. The main sources of interference are DC-DC power supply and TEC temperature control switch noise. The qualified standard is that the amplitude should comply with the limit values of EN 55032, and there should be no abnormal sharp interference.

2. Radiated Emission (RE)
The test frequency range is 30MHz to 6GHz. The space radiated electromagnetic waves are collected from all directions through multi-band antennas. The main sources of radiation are high-speed modulation circuits, high-frequency traces, and poor grounding. The test requires scanning and capturing the maximum radiation value to ensure there are no excessive high-frequency issues.

Electromagnetic Immunity Test (EMS)

1. Electrostatic Discharge (ESD) resistance
Simulate static shocks from the human body and equipment, conduct contact/air discharge tests on the equipment casing and interfaces. The laser's photoelectric chip has weak electrostatic resistance. After the test, there must be no hardware damage, and the optical power and wavelength parameters must not drift.

2. Electrical Fast Transient Pulse (EFT)
Apply transient pulse interference to the power supply and signal ports to verify the stability of the driving and temperature control circuits. The qualified standard is that the equipment does not restart or report errors, and the optical parameters do not fluctuate.

3. Surge Resistance (SURGE)
Simulate lightning strikes and grid voltage fluctuations, suitable for outdoor communication applications of the laser. Ensure that the power circuit does not break down and the equipment does not fail.

4. Radio Frequency Radiation/Conduction Resistance (RS/CS)
Simulate space radio frequency radiation and line coupling radio frequency interference in the 80MHz - 6GHz frequency band. Monitor the laser wavelength, optical power, and modulation accuracy throughout the process. If there is no parameter drift or output abnormality, it is considered qualified.

Conclusion

The core of the EMC test for the 1570nm laser is to control its own interference and resist external disturbances. Different from ordinary electronic products, its test requires a dual determination based on both electrical performance and optical parameters. It is the fundamental basis for ensuring the long-term stable operation of the laser in communication and detection scenarios. The standardized test environment and comprehensive EMI/EMS testing can effectively identify electromagnetic compatibility issues, optimize product design, and enhance the reliability and compliance of the equipment.

 

Frequently asked questions about 1570nm laser EMC testing

What frequency range is covered by conducted emission (CE) testing?
CE testing covers 150 kHz to 30 MHz, measured at the power supply and control ports through a LISN, with limits following EN 55032.

What frequency range does radiated emission (RE) testing cover?
RE testing covers 30 MHz to 6 GHz, scanning for maximum radiated values caused by high-speed modulation circuits, high-frequency traces and poor grounding.

What test site is required for 1570nm laser EMC testing?
A conventional 10-meter semi-anechoic chamber is used; small samples may use a 3-meter chamber. The site must cover 150 kHz to 6 GHz with background noise well below the test limits.

Why is EMC testing of a 1570nm laser different from ordinary electronics?
The device is not a pure optical component: qualification requires dual judgement on both electrical performance and optical parameters such as wavelength, optical power and modulation accuracy, monitored throughout the immunity tests.

RELATED READING

RECOMMENDED PRODUCTS

Hardware configurations from the ERDI Laser catalogue that match the topics in this article:

Back to the blog title

Post comment

Please note, comments need to be approved before they are published.