Free shipping for orders more that $200
Free shipping for orders more that $200

Cart

Your cart is currently empty.

Continue shopping
1 / 4

905nm Laser Rangefinder Module 1km

Chat With Us

Reply within 24 hours

Delivery Time

3-5 days after payment

Shipment

Air freight

DESCRIPTION

ERDI Laser's newly developed laser ranging module. This 905nm laser ranging module employs Time-of-Flight (TOF) technology to achieve high-precision distance measurement (5-1000m range) by calculating laser beam round-trip time. Featuring direct TTL-to-MCU connectivity, compact form factor (<10.5g), and low power consumption, it is suited for autonomous systems, surveying equipment, and industrial automation. Its extremely small size makes the product very popular.

TECHNICAL SPECIFICATIONS

Performance Indicators

Eye safety class

Class 1(IEC 60825-1)

Laser wavelength

905±10nm

Laser divergence angle (typical)

4×6mrad

Receiver field of view

~8mrad

Maximum range

(Visibility ≥ 6Km)

≥1000m @70% reflectivity, building targets

Minimum range

5m

Ranging accuracy

(Construction target)

d≤200m:±0.7m

d>200m:±(0.7+0.0004*d)m (d represents distance, in meters)

Measurement frequency

1~3Hz

Accuracy rate

≥98%

Measurement resolution

0.1m

Electrical Specifications

Baud rate

15200bps (factory setting)/57600bps/38400bps/9600bps

Interface type

UART(TTL_3.3V)

Supply voltage

DC 3.3V~5V

Standby power consumption

≤0.5W

Operating power consumption

(+3.3Vin)

≤0.85W

Startup time

≤550ms

Physical characteristics

Weight

10±0.5g

Dimensions

Φ17×37.2 mm

Shock

1200g,1ms

Vibration

5~50~5 Hz, 1 octave/min, 2.5g

Environmental adaptability

Operating temperature

-20~+70℃

Storage temperature

-25~+75℃

Reliability

MTBF≥1500h

OUTLINE DIMENSION(mm)

PIN INTERFACE

Interface Type: UART (TTL_3.3V)

Connector Model: HC-0.8-6PWT

Pin

Definition

Description

1

GND

Ground wire

2

VCC

3.3V DC power supply

3

NC

Empty pin

4

TX

Serial port transmitting end, TTL_3.3V level

5

RX

Serial port receiving end, TTL_3.3V level

6

Power - EN

Low level to power on

POWER - EN Control Instructions:

  1. Pull down <0.3V to disable the module; pull up >3V to enable the module.
  2. Pull from low to high during operation, with a 300mS delay to read data.

The 905nm Laser Rangefinder Module 1000m delivers precise distance measurements from 5 to 1000 meters using advanced TOF technology. Featuring a UART (TTL_3.3V) interface, it supports both single-shot and continuous modes, plus PC software for easy, standardized configuration.

 

APPLICATION NOTES

This module measures 5 m to ≥1000 m against 70% reflectivity building targets under visibility of ≥6 km, at 905 ± 10 nm with Class 1 eye safety to IEC 60825-1, a 4 x 6 mrad divergence, an ~8 mrad receiver field of view and a 1~3 Hz rate. At 10 ± 0.5 g in a Ø17 x 37.2 mm body fed from DC 3.3~5 V at ≤0.85 W in operation, it is suited to autonomous systems, surveying equipment and industrial automation modules where the host supplies the rail directly.

A 0.1 m measurement resolution, an accuracy rate of ≥98% and ±0.7 m accuracy to 200 m widening to ±(0.7 + 0.0004 x d) m beyond describe a unit intended for target position capture rather than surface profiling, and the 5 m minimum range keeps close-in objects inside specification. Shock of 1200 g for 1 ms, 2.5 g vibration, ≤550 ms startup, -20 °C to +70 °C operation, storage from -25 °C to +75 °C and MTBF ≥1500 h allow it to be fitted to outdoor handheld and vehicle-mounted equipment.

SELECTION GUIDANCE

Select this module where 1 km of standoff, 10 g and acceptance of both 3.3 V and 5 V rails decide the design. Where the same targets must be reached at 1.5 km or 2 km, the longer members hold the 3.3 V rail and the 1~3 Hz cadence but need a larger, heavier housing; where centimetre accuracy below 10 m and 20 Hz to 10 kHz rates are required, the 905 nm LiDAR family is the correct comparison; where Class 1 operation is needed among people at long standoff, 1535 nm modules are the class to evaluate.

At acceptance, verify ≥1000 m under visibility ≥6 km and 70% reflectivity, the 5 m minimum range, the accuracy formula on both sides of 200 m, 0.1 m resolution, an accuracy rate of ≥98%, the 1~3 Hz rate, ≤550 ms startup, ≤0.5 W standby and ≤0.85 W operation, the 3.3~5 V input window, the 10 ± 0.5 g mass in Ø17 x 37.2 mm, and the 1200 g, 1 ms shock and 2.5 g vibration ratings.

FREQUENTLY ASKED QUESTIONS

What is the maximum range of the 905nm Laser Rangefinder Module 1km?
The specified maximum range is ≥1000 m at 70% reflectivity against building targets, with visibility ≥6 km. The minimum range is 5 m.

Which supply voltage range does the 1 km module accept?
It accepts DC 3.3V~5V and connects to an MCU directly through its UART (TTL_3.3V) interface.

What are the weight and dimensions?
The module weighs 10±0.5 g and measures Φ17×37.2 mm.

What ranging accuracy and resolution does it provide?
For targets at d≤200 m the accuracy is ±0.7 m, and for d>200 m it is ±(0.7+0.0004*d) m. Measurement resolution is 0.1 m.

How is the Power-EN pin used to enable the module?
Pull the pin down below 0.3 V to disable the module and up above 3 V to enable it. When pulling from low to high during operation, allow a 300mS delay before reading data.

ORDERING INFORMATION

Is there a minimum order quantity?
There is no minimum order quantity. Single units and evaluation samples are accepted.

What is the sample lead time?
Samples are shipped within 1 week after order confirmation.

What is the batch production lead time?
Batch production is delivered within 1 month after order confirmation.

RELATED TECHNICAL GUIDES

Further ERDI Laser engineering references on 905 nm compact laser rangefinder modules:

905nm Laser Rangefinder Module 1km 905nm Laser Rangefinder Module 1km 905nm Laser Rangefinder Module 1km 905nm Laser Rangefinder Module 1km

You may also like